AutomateDirectUSAMotion LibraryShop the parts catalog

Selection guide

Pneumatic valve setup for double-acting robot grippers

Pneumatics and hydraulics Published 8 min read

Short answer

One 5/3 double-solenoid valve with a chosen center runs a single double-acting gripper cylinder: coil A closes, coil B opens, both off gives the idle state you ordered. Two spring-return valves on one manifold usually feed two functions — equalization, safety lock, cascaded exhaust — not one cylinder. Size the valve on peak flow: the worked example needs about 264 L/min at close.

On this page
  1. How many valves does a double-acting gripper cylinder need?
  2. What does the ISO 5599-2 standard fix when you pick a valve?
  3. Which center position should the valve have, blocked or exhaust?
  4. Why do dressed robots show two spring-return valves on one manifold?
  5. How much air does a double-acting gripper use per cycle?
  6. What valve flow closes the jaws on time?
  7. Does a double coil shift faster than a spring return?
  8. What is the pick for each gripper case?
  9. Questions asked

One double-acting gripper cylinder takes one 5/3 double-solenoid valve: coil A closes the jaws, coil B opens them, both coils off leaves the spool detented at center, so the idle state is the center condition you order, not extra hardware. The two spring-return valves you see on a dressed robot's manifold are usually two separate functions — an equalization cylinder, a coolant valve, a safety lock, a cascaded exhaust — not the two directions of one cylinder. This article gives you the standard behind the valve base, the center-position decision, the air and flow arithmetic for a worked 40 mm example, and the final pick for each case.

How many valves does a double-acting gripper cylinder need? #

One: a single 5/3 double-solenoid valve does the whole job, with coil A closing the jaws, coil B opening them and both coils off leaving the spool detented where it sits, so the idle state is set by the center condition you order rather than by extra hardware.

Solenoid count is the trap. Two coils on one valve body means one valve with a held center; one coil per valve on a manifold means each is a spring-return unit with a duty of its own. For a single cylinder the 5/3 double-solenoid also wins on plumbing: one subplate, one supply connection, two exhaust ports, two controller outputs, and a hold or a dump at idle, decided by the spool you order.

Two single-coil 3/2 valves, one per cylinder port, can technically run a double-acting cylinder — energize either to fill its port, both off dumps both sides — but that spends two bases and two exhausts to reach only the relax-at-idle behavior a center-exhaust 5/3 gives you in one.

What does the ISO 5599-2 standard fix when you pick a valve? #

ISO 5599-2 is the mounting-interface standard for five-port directional valves: it fixes the port positions and hole pattern of the subplate, size class by size class, with optional electrical connector locations, so a size 2 valve from one compliant maker drops onto another maker's size 2 base.

The published edition is ISO 5599-2:2001, amended by Amd 1:2004, and its subject line says exactly what it governs: mounting interface surfaces for five-port directional control valves, with optional electrical connector. What that buys you on the bench: a manifold or valve-island base drilled for one compliant size 2 valve accepts any other compliant size 2 valve, so tubing, manifold pattern and spare-valve interchange all survive a change of valve maker. Families built to it are sold for this duty; the Numatics Series 5599-2 (size 2) is documented as high-speed, heavy-duty valves for general service on all types of automation.

One documented feature worth ordering deliberately: on ISO 5599/2-series valve units, the No. 3 and No. 5 ports contain adjustable needle valves, so the flow of exhaust air leaving the valve unit can be throttled right at the base — a first speed-control handle for the jaw stroke without adding cylinder-mounted fittings. Verify the feature on the datasheet of the exact body you buy.

Which center position should the valve have, blocked or exhaust? #

Pick the center from the idle state the part can survive: center-exhaust dumps both cylinder lines and lets the jaws relax when both coils are off, while center-blocked shuts every port and holds both lines' pressure through a pause — for only as long as the trapped air holds.

The third center, all ports fed from supply, has no place on the shortlist for a single-rod gripper: equal pressure on both sides pushes the piston toward full extension, because the cap side has more area, and the jaws creep open. For the other two, decide with the failure path in mind. Center-blocked is a pause, not a lock: trapped air leaks down through seals and fittings and the jaws drift with whatever force acts on them, which is why air loss means drift, not lock for double-acting actuators generally. Where a dropped part can reach a person, the cell's risk assessment decides the loss-of-air state, under ISO 10218-2 for robot integration and ISO/TS 15066 for collaborative grippers — a blocked-center valve is an input to that assessment, not the answer to it.

Why do dressed robots show two spring-return valves on one manifold? #

Because the second valve usually serves a second device, not the second direction: on dressed weld guns and grippers, tracing the tubing most often finds an equalization cylinder, a coolant valve, a safety lock with a plugged secondary port or a cascaded two-speed exhaust behind it.

Equalization is the clearest case. On a self-centering weld gun the clamp rides in a yoke on a common pivot, so the electrodes pinch the sheet at its center instead of shoving it out of position; that float is its own small cylinder with its own valve. Robot builders sell it as a function, not as wiring convenience — Motoman lists electrode equalization among its spot-welding capabilities, and KUKA.EqualizingTech equalizes the gun by moving the robot itself. A second valve can also be a safety lock with a blocked secondary port, a cascaded pair for a two-speed exhaust, or simply extra exhaust capacity behind a third silencer. Map what you see before you credit either valve with a cylinder direction:

What you see on the robot What it usually means What you do
One 5/3 double-solenoid valve One actuator with close, open and a chosen idle state Confirm the center condition (exhaust or blocked) and the detent before wiring
Two single-coil spring-return valves on a manifold Two separate functions: equalization cylinder, safety lock, coolant valve, cascaded exhaust Trace every tube and port before crediting either valve with a cylinder direction
Three or more exhaust silencers Extra exhaust flow needed, or a one-function valve with a plugged port Count the silencers, find plugged ports, check exhaust restriction against the stroke time
A small second cylinder or a yoke pivot at the clamp Equalization float, or a preload return on a single-acting spring-open gun Plumb the equalization circuit separately from the electrode force circuit

How much air does a double-acting gripper use per cycle? #

For a 40 mm bore, 16 mm rod, 100 mm stroke cylinder at 6 bar gauge (7 bar absolute), one full close-and-open cycle moves about 1.6 liters of free air — 0.232 L of compressed volume multiplied by the 7 bar absolute supply ratio.

Inputs: bore 40 mm, rod 16 mm, stroke 100 mm, supply 6 bar gauge, atmospheric taken as 1 bar. This is a calculated example for those inputs, not a measured result.

  • Cap-side area: A1 = 0.7854 × 40² = 1256.6 mm².
  • Rod-side annulus: A2 = 1256.6 − (0.7854 × 16²) = 1256.6 − 201.1 = 1055.5 mm².
  • Chamber volumes at full stroke: V1 = 1256.6 mm² × 100 mm = 125,660 mm³ = 0.126 L; V2 = 105,550 mm³ = 0.106 L.
  • Compressed volume moved per close-and-open cycle: 0.126 + 0.106 = 0.232 L.
  • Free air per cycle: 0.232 L × 7 = 1.62 L.
  • Branch average at 20 cycles/min: 1.62 L × 20 = 32.4 L/min.

Add line and fitting volume on top — a few percent with a valve mounted at the gripper, more when it sits in the cabinet. The average matters to the supply branch; the valve itself never sees it.

What valve flow closes the jaws on time? #

Size the valve on the peak stroke, not the average: filling that 0.126 L cap side in 0.2 s demands about 264 L/min of free air through the valve, so the body you buy must show a datasheet flow at 6 bar that clears 264 L/min with margin.

  • Compressed flow to fill the cap side in 0.2 s: 0.126 L ÷ 0.20 s = 0.63 L/s.
  • As free air: 0.63 L/s × 7 = 4.41 L/s, and 4.41 × 60 = 264 L/min.
  • Air actually carried by one close stroke: 0.126 L × 7 = 0.88 L — at this scale the shop supply is never the constraint; the valve's instantaneous flow is.

Take the body size from its rated flow at working pressure in the datasheet, with margin for tubing, fittings and silencers — a clogged silencer slows the stroke as surely as an undersized valve. Set jaw speed with exhaust metering: the needles in base ports 3 and 5 for coarse control, meter-out flow controls at the cylinder ports for the steadier hold through the stroke.

Does a double coil shift faster than a spring return? #

Yes: a coil drives the spool with full magnetic force over the whole travel, while a spring's push decays as the spring relaxes toward rest, so the release stroke of a single-coil spring-return valve is the slower stroke — a double coil gives both directions the same drive.

That is why cycle-critical clamp and weld-gun circuits order the double coil: close and open both get the same electromagnetic shift, and neither stroke waits on a spring. If cycle time is tight, read both shift times from the valve datasheet instead of assuming the two strokes match, and time the actual valve on the machine by triggering a shift against the controller clock. When a spring shift is mandatory — a jaw that must open on loss of control power — the slower release belongs in the cycle budget as a designed number, not as a surprise.

What is the pick for each gripper case? #

One double-acting gripper that must hold through a pause takes one 5/3 double-solenoid valve, center-blocked; one that may relax at idle takes the same valve center-exhaust; an inherited two-valve manifold gets its ports traced; a cycle-critical axis gets the peak-flow number, not the average.

  • New build, one double-acting gripper, the part must stay held through a pause: one 5/3 double-solenoid valve, center-blocked, detented. Both coils off is the hold state.
  • New build, jaws may relax between cycles: the same valve body ordered center-exhaust; idle dumps both lines and the jaws go slack by choice.
  • Existing manifold with two single-coil valves: trace every tube first. Only the valve that actually feeds the cylinder counts; the other stays a separate circuit with its own function.
  • Cycle-critical jaw: double-solenoid for symmetric shift speed, body chosen on the peak-flow number — 264 L/min free air in the worked example — never on average consumption.

The rule behind all four: count functions, not solenoids; trace ports before plumbing; size the valve on the fastest stroke.

Questions asked

Can a single-solenoid spring-return 5/2 valve run a double-acting gripper?

Yes, and it is the right body when the jaws must open on loss of control power: energize the coil to close, and the spring shifts the valve to open when the coil drops. It needs one controller output instead of two, it gives up any hold-at-idle state, and its release stroke is the slower spring shift — read that return time from the datasheet before committing the cycle.

What do the port numbers on a five-port valve mean?

Port 1 is supply. Ports 2 and 4 are the working outputs to the cap and rod lines of the cylinder, and ports 3 and 5 are the exhausts. On an ISO 5599-2 size base these positions are fixed on the subplate, so tubing, manifold drilling and spare-valve interchange survive a change of maker within the same size class.

Can one valve run two gripper cylinders?

Only when both jaws must always move together: tee both cylinders into ports 2 and 4 and they extend and retract in unison. Paralleling also splits the flow, so both cylinders stroke slower than one alone, and neither jaw can have its own timing or idle state. The moment either jaw needs independence, give it its own valve.

Should the valve sit on the robot arm or in the cabinet?

At or near the gripper when cycle time matters. Long, small-bore lines add trapped volume to each chamber, which stretches the fill time behind the flow calculation and makes jaw speed harder to tune with exhaust throttling. Cabinet mounting suits slow clamps and cells where washdown, vibration or access rules put the valve island away from the arm; budget the line volume as extra cylinder volume when you size.

Keep reading

  • Selection guide

    Choosing an Actuator to Compress a Small Spring Precisely

    A 2 lbf (8.90 N) spring over 0.5–0.75 in of travel at 0.025 in steps is a screw problem, not a motor problem: a manual fine-lead screw with a locknut holds the setting with no power. Add a stepper only for remote adjustment, an integrated actuator for automated sequences, or a pneumatic cylinder with an adjustable stop when only endpoint positions matter.

    Motors, gearboxes and drives sizing