AutomateDirectUSAMotion LibraryShop the parts catalog

Selection guide

Selecting a 180 Degree Helical Rotary Pneumatic Actuator

Pneumatics and hydraulics Published 8 min read

Short answer

Yes, purpose-built 180-degree pneumatic rotary actuators exist as catalog items from several makers. Size one from the worst-case load torque measured at the driven shaft and the pressure measured at the actuator ports during motion. Doubling rotation in the same helical housing halves ideal torque, so never stretch a 90-degree rating to 180 degrees.

On this page
  1. Why doubling the rotation halves ideal torque
  2. What is documented as available
  3. What to measure before you pick a size
  4. Sizing the 180-degree torque budget from an 87 in-lb mechanism
  5. Stretched 90-degree unit or purpose-built 180-degree unit
  6. Valve flow, cushioning and shaft loads
  7. Verifying the installation
  8. Questions asked

Purpose-built 180-degree pneumatic rotary actuators exist as catalog items, not specials. PHD lists its Series RF pneumatic rotary actuator with 180 degrees as the standard rotation in 14, 20 and 25 mm bores, SMC lists arcs of 90, 180, 190 and 270 degrees, and one heavy-duty line documents 16 base models from 87 to 1000 in-lb across 45, 90, 180 and 270 degree rotations. The hydraulic 90-degree units that dominate search results are a different family, rated for oil. Pick the pneumatic unit from the worst-case load torque at the driven shaft and the pressure measured at the actuator ports during motion, because doubling rotation in the same helical housing roughly halves ideal output torque. The physics, the documented options, the measurements, one worked torque budget, and the decision for each case follow.

Why doubling the rotation halves ideal torque #

A helical rotary actuator pushes a piston along a helix, so a limited linear stroke becomes angular output. For an ideal mechanism, linear work in equals rotary work out:

F × x = T × θ

where F is linear force, x is stroke, T is output torque and θ is rotation in radians. Rearranged, T = F × x / θ.

Keep the housing, the force and the stroke, and open the sweep from 90 degrees (1.5708 rad) to 180 degrees (3.1416 rad): θ doubles, so ideal torque falls to one half. Friction and seal drag take more off the top.

A maker therefore buys 180 degrees one of two ways. Change the helix angle in the same envelope and accept about half the torque, or increase the stroke and the force-producing area and accept a bigger actuator. Diaphragm-driven helical designs sit at the sharp end of that trade, because a diaphragm's travel is short, so doubling rotation pushes toward roughly double the stroke-producing scale. Do not assume which route a candidate takes: read its sectional drawing or ask the manufacturer.

Rack-and-pinion is the mechanically easy route to long rotation, since it only needs longer racks in a longer cylinder, which is why it keeps coming up as the default answer. If it is out for your machine, write down the specific reason, whether backlash, envelope or shaft interface, so a supplier does not quote it back at you.

What is documented as available #

Searching on the word helical alone surfaces hydraulic lines, because hydraulics owns the torque-dense end: most hydraulic rotary actuators carry a maximum pressure rating of 1500 psi (100 bar), with documented exceptions such as Parker's Helac L30 series at 3000 psi and 17,000 to 215,000 in-lb. Those ratings assume oil. Running compressed air through a hydraulic actuator is not a rated operating mode, and its leakage and lubrication behavior is wrong for air, so do not do it.

Pneumatic units are cataloged by rotation and torque rather than by mechanism, and whether a given family is helical, rack-and-pinion or vane is a datasheet item. Typical operating pressure for pneumatic actuators is quoted as a 3 to 10 bar (43 to 145 psi) band, varying by model, and output torque scales directly with supply pressure.

Documented line Medium Rotations Torque span What it settles
PHD Series RF Pneumatic 180° standard; bores 14, 20, 25 mm published per bore 180-degree pneumatic rotation is a standard catalog item
SMC rotary actuator units Pneumatic 90°, 180°, 190°, 270° per configuration arcs at and beyond 180° in one family
Heavy-duty rotary line, 16 base models Per series 45°, 90°, 180°, 270° 87 to 1000 in-lb a wide torque span with 180° mid-range
Parker Helac L30 Hydraulic Per catalog 17,000 to 215,000 in-lb at 3000 psi the hydraulic family that dominates searches; not an air substitute

The exact torque for a given model, pressure and rotation comes from that model's current datasheet; none of these lines publishes one universal number.

What to measure before you pick a size #

  • Worst-case load torque across the whole 180-degree sweep, taken at the driven shaft: breakaway torque, running torque and the highest-load position, including gravity where the sweep lifts, seal drag, bearing friction and process forces.
  • Port pressure during motion, read with a gauge at the actuator port at the highest-flow part of the cycle, not the regulator setting upstream. A large gap between supply and port pressure during motion points to a restriction in the valve, tubing, fittings or silencers.
  • Required rotation time and duty pattern, and the load inertia reflected to the shaft.
  • Mounting orientation, shaft interface, envelope, end-of-travel impact allowance, cushioning options, and position feedback needs.
  • Backlash and lost motion measured at the load where the motion reverses, not judged at the actuator shaft alone.

The discipline is the one used when sizing a hydraulic cylinder bore for a linked lift: worst-case load at the pressure actually available at the actuator, never nameplate conditions.

Sizing the 180-degree torque budget from an 87 in-lb mechanism #

Inputs #

  • Base rating T90 = 87 in-lb over a 90-degree sweep: the low end of the documented 87 to 1000 in-lb line, used here as an example input, not a specific model's datasheet value.
  • θ90 = 90° = 1.5708 rad; θ180 = 180° = 3.1416 rad.
  • Rating pressure 10 bar (145 psi): the top of the documented 3 to 10 bar pneumatic band, taken as the basis of the rating.
  • Measured port pressure during motion 5 bar (72.5 psi): inside the same band; in a real selection this is your gauge reading.

Rule #

For an ideal mechanism, F × x = T × θ, so at fixed force and stroke torque is inversely proportional to rotation, and torque also scales in direct proportion to pressure.

Arithmetic #

  • Work constant: F × x = 87 in-lb × 1.5708 rad = 136.7 in-lb·rad.
  • Torque at 180 degrees: 136.7 in-lb·rad ÷ 3.1416 rad = 43.5 in-lb, one half, exactly as the geometry says.
  • Derate to port pressure: 43.5 in-lb × 5 bar ÷ 10 bar = 21.8 in-lb, about 2.5 N·m.
  • Apply the sizing margin, a rule of thumb of worst-case load at no more than half of available torque: 21.8 in-lb ÷ 2 = 10.9 in-lb, about 1.2 N·m.

Decision #

With these inputs, any mechanism needing more than about 11 in-lb (1.2 N·m) at its worst position rules this unit out: fix whatever drops only 5 bar onto the port, or move up a frame in a purpose-built 180-degree line. Below that figure the choice stands on paper; confirm it by test, because this arithmetic is ideal and friction is not in it. This is a calculated example for these inputs, not a measured result.

Stretched 90-degree unit or purpose-built 180-degree unit #

If a manufacturer documents 180 degrees for that exact mechanism, with a torque figure at a stated pressure, that is a rated configuration: use it. What you may not do is take a 90-degree headline rating and call it good at 180 degrees; the conversion is the maker's to publish, and the physics above says which way it moves.

Case Decision
Catalog 180-degree pneumatic unit meets worst-case load at minimum port pressure with margin Specify it, and record the pressure basis on the drawing
Torque short only at low port pressure Fix the flow path first (valve size, fittings, tubing, silencers), then re-run the numbers
Only a 90-degree rating exists for the envelope you want Treat ideal torque as halved with losses on top, and move to a purpose-built 180-degree line
A hydraulic unit is the only envelope fit Change the envelope or the medium; do not put air through an oil-rated actuator

When no catalog unit fits, request a purpose-built 180-degree configuration and ask for torque-versus-pressure data, the rotation tolerance and how it is adjusted, allowable shaft loads, cushioning options, and mounting dimensions. State your measured worst-case torque and port pressure in the request so the answer comes back sized rather than generic.

Valve flow, cushioning and shaft loads #

A 180-degree sweep passes twice the air volume of a 90-degree sweep in the same mechanism, so cycle speed is set by the valve and plumbing as much as by the actuator. A correctly sized actuator behind a restrictive path still travels slowly; that is the diagnosis when static torque is fine but the sweep crawls. Valve a double-acting rotary actuator the way any double-acting cylinder is valved, with the same four-way valve and flow-control thinking as a pneumatic valve setup for double-acting robot grippers.

Rotational inertia arriving at end of travel is where these drives destroy themselves. Use the manufacturer's permitted cushioning or an external stop rated for the load, and set the deceleration deliberately; never let the driven load hammer the actuator's internal limit at full speed.

Check external radial, axial and overturning loads against the output shaft's published bearing limits, and add an outboard support when the driven mechanism would otherwise use the actuator as a structural bearing. A pressurized rotary actuator holds stored energy and its sweep is a pinch point: vent the supply, verify zero energy at the shaft, and follow the machine's lockout procedure and risk assessment before reaching into the envelope.

Verifying the installation #

Run it uncoupled first, at reduced speed, in both directions: full 180 degrees, smooth travel, repeatable endpoints, correct rotation sense. Then couple the load and step the speed up while trending port pressure and shaft angle through representative cycles. Test the position where torque is highest, at the lowest normal supply pressure and the highest credible process load; nominal unloaded operation proves only that the mechanism moves. After cycling, re-check rotation time and endpoint repeatability, and inspect the mount, coupling, stops, tubing and fittings for movement or leakage.

Questions asked

Does a 180-degree helical actuator always deliver half the torque of the 90-degree version?

Only in the idealized case where the same force and stroke drive twice the rotation. A purpose-built 180-degree unit usually recovers torque with a longer stroke or a larger piston, which costs envelope size, so its rating can sit close to a same-family 90-degree unit in a bigger package. The halving math is what happens when only the helix changes in the same housing. Size from the 180-degree unit's own datasheet torque at your minimum port pressure.

Can I adjust a 90-degree rotary actuator to 180 degrees with its stops?

Not unless the manufacturer documents that rotation range for that exact model. Stop adjustment works within a limited band around the designed sweep; 90 to 180 degrees is a mechanism change, not a stop change, and forcing it pushes the piston into a region the cushioning was never designed for. Ask the maker for the adjustable rotation band before counting on it.

Why do searches return so many hydraulic 90-degree helical actuators?

Hydraulic helical designs dominate because oil at a 1500 psi class rating, with documented lines to 3000 psi, packs far more torque per size than air at 3 to 10 bar. Many of those lines also standardize on 90-degree sweeps. Pneumatic 180-degree units are cataloged under rotary actuator families rather than under the word helical, so search by rotation and torque, not by mechanism type.

How much torque margin should a pneumatic rotary actuator carry?

Rule of thumb: hold worst-case load torque at or below half the available torque at the lowest port pressure you will actually see during motion. That margin covers friction your estimate missed, pressure dips during high flow, and seal wear over service life. High duty cycles or critical positioning need more; where the maker publishes a sizing worksheet, it overrides the rule.

Keep reading

  • Comparison

    Electric vs pneumatic butterfly valve actuator comparison

    Choose a modulating electric actuator when the valve must hold set positions between open and closed under a digital command and you would rather not run compressed air to it; choose pneumatic when the 90° stroke must finish in one to three seconds, when the process needs a spring-driven fail-safe action, or when the valve sits somewhere an electric drive would need certified explosion-proof construction. Size either type to exceed the valve's break torque by at least 25% at minimum supply pressure, on an ISO 5211 mounting interface.

    Pneumatics and hydraulics

  • Selection guide

    Choosing an Actuator to Compress a Small Spring Precisely

    A 2 lbf (8.90 N) spring over 0.5–0.75 in of travel at 0.025 in steps is a screw problem, not a motor problem: a manual fine-lead screw with a locknut holds the setting with no power. Add a stepper only for remote adjustment, an integrated actuator for automated sequences, or a pneumatic cylinder with an adjustable stop when only endpoint positions matter.

    Motors, gearboxes and drives sizing

  • Selection guide

    Pneumatic valve setup for double-acting robot grippers

    One 5/3 double-solenoid valve with a chosen center runs a single double-acting gripper cylinder: coil A closes, coil B opens, both off gives the idle state you ordered. Two spring-return valves on one manifold usually feed two functions — equalization, safety lock, cascaded exhaust — not one cylinder. Size the valve on peak flow: the worked example needs about 264 L/min at close.

    Pneumatics and hydraulics