AutomateDirectUSAMotion LibraryShop the parts catalog

Selection guide

Sizing BLDC Torque and Reduction for a Robot Arm Joint

Motors, gearboxes and drives sizing Published 7 min read

Short answer

Size each robot arm joint by the continuous output torque it must hold at the required speed, not by motor wattage. A 5 lb payload held 500 mm from the shoulder axis demands about 11.1 N·m of gravity torque before any link mass, so that joint fixes the reduction ratio and the motor's continuous current. If loaded holding current exceeds about 80% of the continuous rating, change the motor or raise the ratio.

On this page
  1. What sets the torque at each joint
  2. Worked example: sizing the shoulder joint for a 5 lb payload at 500 mm reach
  3. Check the speed envelope before fixing the ratio
  4. Compare the reduction options, then commit
  5. Holding current is the test that fails first
  6. Close the loop on the joint output
  7. The order to work it in
  8. Questions asked

Size every joint of a robot arm by the continuous output torque it must hold at its required speed — not by the motor's wattage. On the joint that decides the build, a shoulder carrying a 5 lb (2.27 kg) payload 500 mm from the axis, gravity alone demands about 11.1 N·m before a single link is counted. Divide that by the reduction ratio and its efficiency and you have the torque the motor must produce continuously, which sets current, heat, and the ratio itself. This article works that joint end to end and gives the rule for when to abandon a low-ratio design.

What sets the torque at each joint #

Gravity torque at a joint is each mass times gravitational acceleration times the perpendicular distance from the joint axis to that mass's line of action — the horizontal offset when the arm is level, which is the worst case for a pitch joint. The payload is only the first term: every link and every downstream motor adds its own mass-times-offset, and a shoulder carries all of them.

During motion, add the acceleration term: joint torque also equals the total inertia about the axis times angular acceleration. The configuration with the highest gravity torque, arm fully extended, is not necessarily the one with the highest acceleration torque, and a fast move of an upstream axis changes what a downstream joint feels. Compute each joint's demand in its own worst configuration, then add margin; the shoulder is almost always the binding joint.

Worked example: sizing the shoulder joint for a 5 lb payload at 500 mm reach #

Inputs, each with its source:

  • Payload: 5 lb = 2.27 kg (the arm's design target).
  • Horizontal offset from the shoulder axis: 0.500 m (the specified reach).
  • Required output speed: 2 rev/s (design target).
  • Motor: Kv 90 rpm/V; the listing states 45 V, 22 A, 900 W (manufacturer listing).
  • Reduction ceiling: 10:1, from the quasi-direct-drive target.
  • Transmission efficiency: assumed 0.90 for this example — take the real value from the datasheet of the exact cycloidal stage or belt drive you use.

The rule in words: gravity torque equals mass times 9.81 m/s² times the horizontal offset. The torque constant comes from Kv as 9.55 (which is 60/2π) divided by Kv in rpm/V.

Arithmetic, joint side:

2.27 kg × 9.81 m/s² = 22.3 N of payload weight 22.3 N × 0.500 m = 11.1 N·m at the shoulder — payload only, a calculated example, not a measured result.

Motor side, first at a 6:1 ratio:

11.1 N·m ÷ (6 × 0.90) = 2.06 N·m of continuous motor torque 9.55 ÷ 90 = 0.106 N·m/A 2.06 N·m ÷ 0.106 N·m/A = 19.4 A, which is 88% of the listed 22 A

The same joint at the 10:1 ceiling:

11.1 ÷ (10 × 0.90) = 1.23 N·m 1.23 ÷ 0.106 = 11.6 A, or 53% of 22 A, at a motor speed of 10 × 2 rev/s = 20 rev/s (1200 rpm)

Decision: hold continuous current at or below 80% of the motor's continuous rating — a rule of thumb, but one that leaves room for link mass, warm copper, and efficiency that degrades from the assumed value. At 6:1 the motor sits at 88% with zero link mass counted, so reject 6:1 for this shoulder. Commit to 10:1, or keep the ratio low only by fitting a larger motor or a lower-Kv winding, then re-run this arithmetic with measured link masses and the reducer's real efficiency before buying anything. The example assumes the listed 22 A is a continuous rating; if the listing means peak or phase current, the margin is smaller and the decision is even firmer.

Check the speed envelope before fixing the ratio #

Motor speed is the ratio times the required output speed, and the motor's permissible speed comes from its documentation, not from Kv alone. Two revolutions per second is 2 × 2π = 12.6 rad/s at the joint; at a 500 mm reach that is a tool-point speed of 12.6 × 0.500 = 6.3 m/s, a geometric figure, not a demonstrated one. The discipline is the same as checking servo speed margin for a rack-and-pinion axis: available motor speed divided by the ratio must clear the demanded output speed with room left for the torque drawn at the same time, because available torque falls as speed rises.

Compare the reduction options, then commit #

Option What it buys What it costs Decide by
Keep the ratio under 10:1 (quasi-direct drive) Backdrivable joint; a collision moves the arm instead of destroying the transmission; the motor feels the load directly The motor supplies nearly all joint torque, so continuous current and heat run high Loaded hold temperature and current margin
Raise the cycloidal ratio Motor torque demand falls in proportion to the ratio Motor speed rises by the same proportion; backdriving and impact tolerance drop Loaded output speed, reversal behavior, backdriving effort
Fit a larger or lower-Kv motor More torque per ampere and more thermal mass at the joint Its own mass becomes gravity load on every upstream joint Net torque margin after adding its mass upstream
Put part of the reduction in a belt stage Low backlash; the motor can sit off the joint axis The belt carries the full joint torque continuously Continuous torque rating in the belt datasheet and the pulley ratio

Reflected inertia moves with the square of the ratio — the load inertia the motor feels falls by N² — which is why reflected inertia in geared servo systems is worth calculating before you fix N. When a belt stage carries that torque, the timing belt is the next part you specify, sized from its datasheet for continuous torque at the pulley speeds involved. The same belt-versus-gearbox trade, argued against a stepper's torque curve, is worked through in belt or gearbox reduction for a stepper robot arm.

Holding current is the test that fails first #

A shoulder holding a load horizontally delivers essentially zero mechanical power while its motor draws full torque-producing current, and copper loss scales with current squared times winding resistance. A motion test that looks smooth proves nothing about this condition. The confirming test is a sustained hold in the worst configuration with the winding temperature trend logged; a thermal fault during that hold means the sizing is wrong, not the limit setting.

Read the listing before trusting its numbers: 45 V times 22 A is 990 W only if both figures are simultaneous DC input values, and whether the 900 W is electrical input or mechanical shaft output changes the margin. Set the drive's current, voltage and thermal limits from the selected motor and drive documentation, and test braking as well as motoring — a falling arm returns energy to the drive, and the supply arrangement has to absorb it. Treat a gravity-loaded arm as stored energy: support it, or confirm it settles predictably on power loss, before anyone reaches into the envelope, under the machine's lockout procedure and the risk assessment ISO 12100 asks of any machine builder.

Close the loop on the joint output #

A 14-bit absolute encoder after the reduction divides one joint revolution into 16,384 counts, about 0.022° per count, so the controller sees true joint angle even as the transmission wears or flexes. Keep commutation sensing on the motor, where it belongs, and take position from the output side. The same question — feedback on the motor shaft or behind the gearbox — is what separates a stepper gearbox encoder from a servo gearhead in precision axes, and the answer there is the answer here: the loop should include everything you intend to control.

The order to work it in #

  1. Compute worst-case gravity torque for each joint with links and downstream motors included, not payload alone.
  2. Pick a candidate ratio and divide: motor torque = joint torque ÷ (ratio × efficiency).
  3. Convert to current with 9.55 ÷ Kv and compare against the continuous rating; above 80%, change the motor or the ratio.
  4. Check motor speed = ratio × output speed against the motor's permissible speed.
  5. Run the sustained-hold temperature test in the worst configuration, then a braking test.
  6. Only then fix the transmission, the feedback, and the wiring.

Questions asked

Which joint should I size first?

The shoulder — whichever pitch joint carries the most mass at the longest moment arm. It sees the payload plus every downstream link and motor, so its continuous torque and holding current are the arm's worst case. A wrist roll carrying a 1 kg tool 80 mm from its axis sees only 1 × 9.81 × 0.08, about 0.8 N·m, and can use a far smaller motor. Size the worst joint first, then scale the architecture down where the load allows.

Is a 900 W motor rating enough for the joint?

No number of watts answers that by itself. A joint holding a load horizontally does mechanical work at essentially zero rate while drawing full torque current, so power ratings say nothing about the condition that sizes the joint. Judge it by continuous current times torque constant times ratio times efficiency, compared against the gravity torque. And check what the listing means: 45 V times 22 A is 990 W only if both are simultaneous DC input values; a phase-current or peak reading makes the usable continuous margin smaller.

How do I get torque per ampere from a Kv rating?

For a BLDC motor with constants defined consistently, torque constant in N·m/A is 9.55 divided by Kv in rpm/V. A Kv 90 motor therefore delivers about 0.106 N·m per ampere, so 2.06 N·m of motor torque needs about 19.4 A. Where the maker publishes a measured torque constant, use it instead — Kv is sometimes defined line-to-line and sometimes per phase, which shifts the conversion.

What resolution does a 14-bit encoder give at the joint?

Fourteen bits split one output revolution into 16,384 counts, about 0.022° per count. At a 500 mm reach, one count is roughly 0.19 mm of tool-point position, before any transmission error. Mounted after the reduction, the encoder reports true joint angle even as the transmission wears or flexes, which is why the output side is the right side for it.

Why keep the reduction under 10:1 at all?

Backdrivability. A low ratio leaves the joint free to move, so a collision deflects the arm instead of loading the transmission toward failure, and the motor senses external forces directly, which contact tasks need. The price is that the motor must supply nearly all the joint torque itself, which is exactly what the holding-current check tests. Raise the ratio only when that check fails and a larger motor is unacceptable.

Keep reading

  • Explainer

    Checking Servo Speed Margin for a Rack and Pinion Axis

    Speed here is kinematics, not tuning: 875 ipm through a 30:1 reducer and a 2-inch pitch-diameter pinion takes about 4,178 motor rpm against a 4,200 rpm ceiling, leaving 22 rpm of margin. Cap the ratio near 24:1, or fit a pinion near 2.5 in pitch diameter, so the motor runs at 80% of rated speed at full feed; the torque budget easily follows.

    Motors, gearboxes and drives sizing

  • Selection guide

    Stepper Gearbox Encoder vs Servo Gearhead for Laser Aiming

    Convert the allowed target displacement into an angular budget before choosing hardware: displacement divided by distance, so 0.1 ft at 300 ft allows about 0.33 mrad. Backlash and loaded repeatability then decide the axis: a preloaded worm or strain-wave gearhead with an encoder on the output shaft meets it, microstepping and frame size do not.

    Motors, gearboxes and drives sizing

  • Selection guide

    Belt or Gearbox Reduction for a Stepper Robot Arm

    Size each joint for worst-case gravity torque first: an 8 kg link at 300 mm reach needs 23.5 N·m, which a 2 N·m-class stepper meets only through roughly 14:1 — past what one practical GT2 pulley stage delivers, so that joint takes a gearbox. The motor-shaft magnetic encoder sees no jumped teeth or arm flex, so a home switch and travel-limit switches are needed either way.

    Servo and stepper motion