AutomateDirectUSAMotion LibraryShop the parts catalog

Comparison

Stopping a Vertical Air Cylinder on a Light Curtain Trip

Pneumatics and hydraulics Published 9 min read

Short answer

Use a 3-position center-pressurized valve with a higher regulated rod-side pressure — the only pneumatic center that balances a vertical load mid-stroke — then let a rod lock hold it. Verify every component in the trapped-air path against the deceleration pressure spike and confirm total stop time against the safety-distance formula Ds = 63 in/s × Ts.

On this page
  1. Which valve center actually stops and holds a vertical load?
  2. What does each 3-position center configuration do on a curtain trip?
  3. How much pressure does each side need to balance the load?
  4. How big is the pressure spike when the trapped air stops the load?
  5. How fast must the cylinder stop to satisfy the light curtain distance?
  6. Does a rod lock stop the cylinder or just hold it?
  7. When is hydraulics or lowering the load the better answer?
  8. Which option should I choose for my machine?
  9. Questions asked

Stopping a vertical air cylinder when a light curtain breaks is a valve-center decision plus two energy checks, and only one center condition does the whole job: a 3-position center-pressurized valve with a higher regulated pressure on the rod side, with a rod lock engaged afterward to hold what the valve stopped. Equal pressure on both sides cannot hold a vertical load, because the rod-side annulus is smaller than the full piston face and the imbalance adds to the load instead of resisting it. This comparison walks the five center options and their failure modes, the two pressures that balance a real load, the pressure spike a pneumatic stop creates in the trapped-air path, and the stop-time budget the light curtain imposes on the whole chain.

Which valve center actually stops and holds a vertical load? #

A 3-position center-pressurized valve with a higher regulated pressure on the rod side is the only purely pneumatic center condition that both stops and holds a vertical load mid-stroke; the example below runs 66 psi on the rod side against 30 psi on the cap side for a 200 lb load.

The stop and the hold are two different problems, and often two different devices. The instantaneous stop is a pressure problem: the valve has to put the cylinder into a state where the load decelerates before a hand arrives. The sustained hold is a leakage problem: whatever trapped air or clamp is holding the load must not let it creep during the minutes the curtain stays broken. The split-pressure center-pressurized valve answers the first problem; a rod lock is the usual answer to the second. A common working combination is the split-pressure center plus a pilot-operated check valve on the port of the chamber the falling load compresses, with the rod lock as the final hold.

What does each 3-position center configuration do on a curtain trip? #

The five centers trade stopping response, load retention and restart behavior; the table lists what each does the moment the curtain breaks and the problems each brings, from free fall with center-open to the plumbing complexity of split pressures.

These centers are the spring-centered, de-energized state of a 5-port, 3-position valve: dropping the solenoids to zero — exactly what a curtain trip through the safety relay does — lands the valve in whichever center it was built with. Catalog names vary, so throughout this article center-open means both cylinder ports exhaust, center-blocked means all ports seal, and center-pressurized means supply reaches both cylinder ports.

Center condition On the curtain trip Known problems
Center-open Both chambers vent; the load falls freely No stopping at all; on re-energize the piston strokes at full speed and can slam tooling at the end of travel
Center-open plus a pilot-operated check on the falling-load port The check traps air in the chamber the load is compressing; the load stops against it Stop is soft and can be too slow for a short safety distance; the trapped side can push the load back up; restart slam remains
Center-blocked, or pilot-operated checks on both ports The cylinder locks wherever it is Stop can still be slow; small drift as trapped air shifts; the load is mechanically stuck, and moving it means bleeding the checks
Center-pressurized, one pressure to both sides Both sides see supply; the load drifts toward the rod end The rod-side annulus is smaller, so equal pressures leave a net downward force that adds to the load (47 lb at 60 psi on the example cylinder)
Center-pressurized, two regulated pressures The load balances and holds mid-stroke Fastest pneumatic response, but needs two regulators and more plumbing, and the deceleration spike check still applies

Two details the table hides. The check valve in the second row goes on the port of the chamber that shrinks as the load falls — the rod-side port on a rod-down cylinder with the load hanging on the rod. And none of this changes the basic valve work: the port layout and speed controls are the same double-acting-cylinder plumbing covered in pneumatic valve setup for double-acting robot grippers; the split-pressure scheme only adds a regulator in each line between valve and cylinder.

How much pressure does each side need to balance the load? #

Set the rod-side pressure so its force on the annulus equals the cap-side force plus the load: for 200 lb on a 3-inch bore, 1-inch rod cylinder with 30 psi on the cap side, the rod side needs 66 psi.

Calculated example for those inputs, not a measured result:

  • Cap-side piston area: π/4 × (3 in)² = 7.07 in²
  • Rod-side annulus: π/4 × (3 in)² − π/4 × (1 in)² = π/4 × 8 in² = 6.28 in²
  • Why equal pressure fails: at 60 psi on both sides, net downward force = 60 psi × (7.07 − 6.28) in² = 47 lb, added to the 200 lb load. That is the drift toward the rod end.
  • Balance condition: rod-side pressure × 6.28 in² = (30 psi × 7.07 in²) + 200 lb = 212 lb + 200 lb = 412 lb
  • Rod-side pressure = 412 lb ÷ 6.28 in² = 66 psi

Check it: 66 psi × 6.28 in² = 415 lb of upward force against 412 lb downward, a 3 lb margin before any seal friction — and friction only helps the hold. Set the two regulators with the load attached and confirm the cylinder stands still in the center position; that is the functional test. A double-rod cylinder makes the two areas equal, so one pressure balances the load and the second regulator disappears, at the cost of a longer package.

How big is the pressure spike when the trapped air stops the load? #

Roughly 180 psi in the worked case: a 200 lb load moving 30 in/s and stopped in 0.25 in puts about 1,130 lb of force on a 6.28 in² annulus, and that spike lands on the cylinder, fittings, tubing and valve in the trapped-air path.

This is a calculated example for those inputs using a constant-deceleration bound; the real peak runs higher because trapped air stiffens as it compresses, so treat the number as a floor.

  • Deceleration: (30 in/s)² ÷ (2 × 0.25 in) = 900 ÷ 0.5 = 1,800 in/s²
  • Load mass: 200 lb ÷ 386 in/s² = 0.518 lb·s²/in
  • Deceleration force: 0.518 × 1,800 = 933 lb; total on the annulus: 200 + 933 = 1,133 lb
  • Peak rod-side pressure: 1,133 lb ÷ 6.28 in² = 180 psi

If the cylinder, fittings, tubing and valves in that path carry a common 150 psi rating, the stop itself exceeds it on the first trip. Everything the trapped air touches must be rated for the deceleration peak, not for supply pressure. The peak scales with the square of speed: the same load at 40 in/s stopped in the same 0.25 in decelerates at 3,200 in/s² and peaks near 296 psi.

How fast must the cylinder stop to satisfy the light curtain distance? #

All hazardous motion must stop inside the safety distance Ds = 63 in/s × Ts — the hand-speed formula the OSHA machine-guarding eTool documents for presses — so the example machine's 62 ms total stop time demands at least 3.9 in of curtain standoff.

Ts is the total time from curtain breach to standstill, and every millisecond has an owner: curtain response, safety relay, valve solenoid shift, then the pneumatic stop. Calculated example for the same machine:

  • Control-side delays, illustrative — take yours from the datasheets: curtain response 15 ms + relay 10 ms + valve shift 20 ms = 45 ms
  • Pneumatic stop time: 30 in/s ÷ 1,800 in/s² = 0.0167 s ≈ 17 ms
  • Ts = 45 ms + 17 ms = 62 ms = 0.062 s
  • Ds = 63 in/s × 0.062 s = 3.9 in

The curtain stands at least 3.9 in from the pinch point on this stop, and farther if the standard you work to adds a penetration or uncertainty allowance on top of the hand-speed formula. The inputs that move the answer: load speed at the moment of violation, bore and stroke (a larger trapped volume stops more spongily), line size and length between valve and cylinder, and trip frequency per shift and over machine life. Mount the curtain closer than the calculated distance and the stop is too slow whichever center you chose. The curtain plus the stop function is one safety function: size and validate it under the machine's risk assessment and the applicable standard.

Does a rod lock stop the cylinder or just hold it? #

It only holds: a rod lock is a spring-applied, air-released clamp on the rod that bites when air disappears, so the cylinder must already be stopped — by the split-pressure center or by trapped air — before the lock can do anything.

The lock grips a rod that is stationary, and it grips harder the instant air pressure is lost, which makes it fail-safe for holding. The sequence is stop first, lock second: the valve strategy decelerates the load, then the rod lock takes over the sustained hold so slow leakage past the spool cannot let the load creep. Because it needs air to release, a rod lock that engages on every curtain trip does real work each cycle — confirm its rated cycle count from the datasheet the way you would a brake's, and never ask it to absorb a moving load.

When is hydraulics or lowering the load the better answer? #

When the load must hang suspended with real anti-fall protection, use hydraulics with an anti-fall valve; when the process allows it, drive the cylinder to full retraction so the load rests on its bottom stop and the stored energy is gone.

Pneumatics is at its best exerting a force from point A to point B and poor at holding a mid-stroke position against a load, because air compresses and every seal leaks a little. For a heavy load that must stay suspended near people, a hydraulic cylinder with an anti-fall valve is the robust answer; if you convert the axis, sizing a hydraulic cylinder bore for a linked lift walks through the bore arithmetic for a load-driven cylinder. The other honest alternative is logic, not hardware: let the curtain trip drive full retraction away from the hazard — completing inside the same stop-time budget — so the load lands on its bottom rest and there is nothing left to hold.

Which option should I choose for my machine? #

Pick the split-pressure center-pressurized valve plus a rod lock when a mid-stroke stop is genuinely required and the load is moderate; pick hydraulics with an anti-fall valve when a heavy load must hang suspended near people; pick full retraction whenever the process allows it.

  • Mid-stroke stop required: 3-position center-pressurized valve, two regulators set by the balance arithmetic, a rod lock for the hold, and every component in the trapped-air path rated above the calculated deceleration peak.
  • Heavy suspended load with personnel exposure: a hydraulic cylinder with an anti-fall valve instead of any pneumatic holding scheme.
  • Process tolerates motion away from the hazard on a trip: full retraction to the bottom rest, still finishing inside the safety distance.
  • Frequent expected trips: a rod lock or brake engaged every cycle, sized for that duty.
  • Never: center-open under a load that can fall and hurt someone.

Questions asked

How do I turn my curtain distance into a stop-time budget?

Invert the hand-speed formula: Ts = Ds ÷ 63 in/s. A curtain standing 12 in from the pinch point gives 12 ÷ 63 = 0.19 s for everything — curtain response, relay, valve shift and the pneumatic stop together. Subtract the control-side delays from your datasheets, and whatever remains is the time the trapped air gets to stop the load.

Why does the tooling slam at the end of stroke after the system re-energizes?

A center-open valve vents both chambers during the trip, so when supply returns, full pressure drives the piston with nothing metering it. Fit meter-out flow controls at both cylinder ports and use a cylinder with adjustable end-of-stroke cushions so the restart stroke decelerates before the end cap, and set the cushions for the actual load rather than as shipped.

Would a double-rod cylinder remove the pressure imbalance?

Yes. A second rod gives both sides of the piston the same area, so a single pressure balances the load in the center-pressurized state and the second regulator disappears. You pay with a longer cylinder package and a second rod seal in the leak budget, and the deceleration spike check on the trapped side is unchanged.

How many curtain trips before a valve-only stop is the wrong design?

Treat routine curtain trips as a duty cycle, not a fault event. If operators break the curtain during normal running, the rod lock engages on every stop, so take its rated cycle count from the datasheet the way you would a brake's. A stop that depends only on compressing trapped air also shifts as seals wear, and a high trip frequency is exactly what wears them.

Keep reading

  • Selection guide

    Pneumatic valve setup for double-acting robot grippers

    One 5/3 double-solenoid valve with a chosen center runs a single double-acting gripper cylinder: coil A closes, coil B opens, both off gives the idle state you ordered. Two spring-return valves on one manifold usually feed two functions — equalization, safety lock, cascaded exhaust — not one cylinder. Size the valve on peak flow: the worked example needs about 264 L/min at close.

    Pneumatics and hydraulics

  • Comparison

    Electric vs pneumatic butterfly valve actuator comparison

    Choose a modulating electric actuator when the valve must hold set positions between open and closed under a digital command and you would rather not run compressed air to it; choose pneumatic when the 90° stroke must finish in one to three seconds, when the process needs a spring-driven fail-safe action, or when the valve sits somewhere an electric drive would need certified explosion-proof construction. Size either type to exceed the valve's break torque by at least 25% at minimum supply pressure, on an ISO 5211 mounting interface.

    Pneumatics and hydraulics

  • Selection guide

    Choosing an Actuator to Compress a Small Spring Precisely

    A 2 lbf (8.90 N) spring over 0.5–0.75 in of travel at 0.025 in steps is a screw problem, not a motor problem: a manual fine-lead screw with a locknut holds the setting with no power. Add a stepper only for remote adjustment, an integrated actuator for automated sequences, or a pneumatic cylinder with an adjustable stop when only endpoint positions matter.

    Motors, gearboxes and drives sizing